|
Linux server.jmdstrack.com 3.10.0-1160.119.1.el7.tuxcare.els10.x86_64 #1 SMP Fri Oct 11 21:40:41 UTC 2024 x86_64
/ usr/ bin/ |
|
|
#!/bin/bash
# scsi_satl
#
# Script to test compliance of SCSI commands on a SCSI to ATA
# Translation (SAT) Layer (SATL). This script was compiled using
# sat-r09.pdf found at www.t10.org .
# The scripts still seems to be valid for sat2r09.pdf .
# The vintage is SPC-3 and SPC-4 (see www.t10.org).
#
# Coverage:
# Command SATL notes
# -------------------------------------------------------
# INQUIRY (standard)
# INQUIRY (VPD: 0)
# INQUIRY (VPD: 0x83) Device identification VPD page
# INQUIRY (VPD: 0x89) ATA Information VPD page
# REPORT LUNS SPC-3, SPC-4 (hardly mentioned in sat-r08c)
# TEST UNIT READY
# REQUEST SENSE
# SEND DIAGNOSTIC default self test
# MODE SENSE(10) draft unclear which mode pages, so ask for all
# ATA PASS THROUGH(16) send IDENTIFY DEVICE command. Assume non-packet
# device, if packet device add "-p" option
#
# This script uses utilities from sg3_utils package (version
# 1.22 or later)
#
# Douglas Gilbert 20090930
log=0
quiet=0
verbose=""
file_err=0
inv_opcode=0
illeg_req=0
not_ready=0
medium=0
other_err=0
recovered=0
sanity=0
syntax=0
timeout=0
unit_attention=0
aborted_command=0
total_err=0
usage()
{
echo "Usage: scsi_satl [-h] [-L] [-q] [-v] <device>"
echo " where: -h, --help print usage message"
echo " -L, --log append stderr to 'scsi_satl.err'"
echo " -q, --quiet suppress some output"
echo " -v, --verbose more verbose output"
echo ""
echo "Check <device> for SCSI to ATA Translation Layer (SATL) support"
}
opt="$1"
while test ! -z "$opt" -a -z "${opt##-*}"; do
opt=${opt#-}
case "$opt" in
h|-help) usage ; exit 1 ;;
L|-log) let log=$log+1 ;;
q|-quiet) let quiet=$quiet+1 ;;
v|-verbose) verbose="-v" ;;
*) echo "Unknown option: -$opt " ; exit 1 ;;
esac
shift
opt="$1"
done
if [ $# -lt 1 ]
then
usage
exit 1
fi
for command in "sg_inq" "sg_vpd" "sg_vpd -p di" "sg_vpd -p ai" "sg_luns" \
"sg_turs" "sg_requests -s" "sg_senddiag -t" "sg_modes -a" \
"sg_sat_identify"
do
if [ $quiet -eq 0 ]
then echo "$command" $1
fi
if [ $log -eq 0 ]
then
if [ $verbose ]
then
$command $verbose $1 > /dev/null
else
$command $1 > /dev/null 2>> /dev/null
fi
else
$command $verbose $1 > /dev/null 2>> scsi_satl.err
fi
res=$?
case "$res" in
0) ;;
1) echo " syntax error" ; let syntax=$syntax+1 ;;
2) echo " not ready" ; let not_ready=$not_ready+1 ;;
3) echo " medium error" ; let medium=$medium+1 ;;
5) echo " illegal request, general" ; let illeg_req=$illeg_req+1 ;;
6) echo " unit attention" ; let unit_attention=$unit_attention+1 ;;
9) echo " illegal request, invalid opcode" ; let inv_opcode=$inv_opcode+1 ;;
11) echo " aborted command" ; let aborted_command=$aborted_command+1 ;;
15) echo " file error with $1 " ; let file_err=$file_err+1 ;;
20) echo " no sense" ; let other_err=$other_err+1 ;;
21) echo " recovered error" ; let recovered_err=$recovered_err+1 ;;
33) echo " timeout" ; let timeout=$timeout+1 ;;
97) echo " response fails sanity" ; let sanity=$sanity+1 ;;
98) echo " other SCSI error" ; let other_err=$other_err+1 ;;
99) echo " other error" ; let other_err=$other_err+1 ;;
*) echo " unknown exit status for sg_inq: $res" ; let other_err=$other_err+1 ;;
esac
done
echo ""
let total_bad_err=$file_err+$inv_opcode+$illeg_req+$medium+$aborted_command
let total_bad_err+=$other_err+$recovered+$sanity+$syntax+$timeout
let total_allow_err=$not_ready+$unit_attention
echo "total number of bad errors: $total_bad_err "
if [ $total_allow_err -gt 0 ]
then
echo "total number of allowable errors: $total_allow_err "
fi
exit $total_bad_err